Spectrum printing reviews

Spectrum printing reviews DEFAULT

3D Printing Industry (3DPI) asked me to test out some filament from a new manufacturer, Spectrum Filament based in the UK.

Over the last four years I have used many different types and sources of 3D printing filament, both good and bad that has been manufactured all over the world, so I agreed to take a look, here are my findings along with some general advice and guidance along the way.

Spectrum manufacturers its filament in the UK and is currently producing PLA in 1.75mm and 3mm, sized for the 3D printing sector.

Horne Image 1

The filament comes packed in cardboard boxes. No bags or desiccant are being used, this is not usually a problem with cardboard as it’s hydroscopic and will absorb ambient moisture.

Horne-Image-2

The filament itself is wrapped around a cardboard and metal core reel, the same sort used for electrical cable.

It would be good to have had some marking on the reel, a label with material name and colour would help identify replacements when re-ordering, it took me some time to match them with the website, and I’m not sure if I have called them by their correct names below.

Metal seam - makes for a noisy filament feed.

One problem with this reel is that the metal seam causes some issues for a typical filament spool holder. The reel clanks over and over this join every few minutes of printing, getting worse towards the end of the reel when it’s lighter and the tight coil pulls the reel forwards. All reel spools need some friction to stop them self unwinding, so depending on how you mount your material this is likely to be a noisy problem for you.

Horne-Image-4

The biggest issue with the current packaging is that cardboard fibers are all over the filament.

Horne-Image-5

It’s a good idea for any filament to use a fluff catcher — regardless of how well it’s been stored you will usually get some debris on the raw filament over time. A simple solution is to use a section of sponge, push the filament through and add some pressure with a zip-tie or rubber band. Have the sponge at the entrance to your extruder drive, I can’t stress enough how important it is not to let fluff, dust and debris into either the extruder drive gear or the hot-end melt chamber. It’s very easy to clog up a 3D printing extruder even with the smallest amount of foreign material that does not melt.

Horne-Image-6-7

I had five filaments to test from Spectrum, Black and White in 3mm diameter, Bronze, Teal and Patriarch in 1.75mm

Horne-Image-8

The filament spools had a consistent weight and after deduction of the empty reel weight (116g) it showed 100m of material was supplied on each.

Horne-Table-1

The next test was to check size, roundness and consistency. For this I measured the start, middle and end of each reel as they were being used.

*Filament is measured twice in the same spot to check roundness.

I found some minor differences in roundness and consistency, this is slightly less of an issue for 3mm material, but the 1.75mm will cause a variety of problems. (See comments further on).

Horne-Image-9

It’s important for the filament to be consistent in both diameter throughout the reel and to also be round, an oval filament causes all sorts of problems with the a variation in volume of material and the feed rate as the extruder drive diameter changes due to size whilst rotating.

I could feel some marks on the filament as I ran my fingers along each length so I examined the surface and also decided to do a more detailed check of the diameter. At regular lengths (every five or six coils) the white 3mm filament was clearly showing indents in the filament, the black had similar but smaller surface imperfections, too hard to photograph.

Horne-Image-10-11

The Patriarch (1.75mm) also had a number of bumps and dimples along the surface, at less regular intervals than the white, but this caused me some concern being on the smaller diameter filament.

Horne-Image-12

I decided to check 10m of the 1.75mm filaments with a home-made die — this is a section of brass with a hole drilled with a 5/64″ bit — to give a metric 1.97mm hole. Experience has shown that this dimension is the very maximum size I can use in a direct drive extruder without causing jamming, skipping or excess nozzle pressure.

Horne-Image-13--14

The Patriarch showed more problems, and at points along the 10m sample section, where pimples were present on the filament, it was a tight fit, I measured around these points and found some widening of the filament along the reel.

Horne-Image-15-16

The widest point measured at 1.88mm for the Patriarch colour.
The Bronze had the tightest fit in the die test, at this point, the die only just pulled over, I suspected this was going to cause me issues with direct drive extruders. Unfortunately I was correct (See comments below.)

A direct drive extruder uses the motor shaft to directly drive the filament. A strong motor is required and as many 3D printers use a constant pinch pressure or very limited movement, fatter diameter filaments can cause issues with this type of drive mechanism. Printers like the Makerbot Replicator, the Afinia (PP3PD), Solidoodle, QUBD and many others are fitted with an extruder drive similar to that in the image here:

Horne-Image-19

I installed Bronze 1.75mm into two different machines both running direct drive extrtuders, the image below was where the Bronze jammed up and the print failed, measuring the diameter it was just above 1.9mm. The Patriarch was a little better but that also jammed up 2 hours into a 15 hour print.

Horne-Image-20

Some issues can often be overcome with a slight increase in extrusion temperature, this was not the case for the Bronze or Patriarch. Another tell-tale issue of over-diameter filament or increased material pressure is with extruder stall, you can hear the extruder skip and jump, and these show up as areas of missing material, usually easier to see on a solid infill. The image below may look like a good solid infill, but in two places from top to bottom there are missing lines just under the top layer, which, on the perimeter of an object, show up as gaps.

Horne-Image-21

The Teal 1.75mm material didn’t jam in any machine, both direct drive and geared. This was also the reel with the best measured tolerances supplied.

Horne-Image-22

Bonding of all material to the bed was excellent, I had no issues at all, with both tiny detailed parts and very large prints.

Horne-Image-23

Despite the pimples and dents in the filament, which do show up on the printed models, I am happy with the properties of the PLA.

Horne-Image-24

All the PLA showed very low warp and bonded well to heated clean glass, coated PVA glass, acrylic and blue tape.

Horne-Image-25

I printed off many of these stones for Project Egg (below image) — these are big parts, 182mm wide and 100mm high. If you get a chance to contribute to Project Egg please take a look and get involved.

Horne-Image-26

This is what 80M of 3mm filament will print out, the large parts are around 130mm wide by 60mm tall, all these parts have a high level of material infill at around 45% to 100% in places:

Horne-Image-27

Horne-Image-28Spectrum reels have a 75mm inner diameter core giving a very tight and springy coil, it’s not going to unwind on you. I’m not a big fan of small reels, I do use some with 1.75mm material, but generally I will not buy 3mm material if it’s very tightly wound on a small reel, this is one area we as an industry need to get a more common and agreed standard on the mechanical dimensions of spool sized and mounting methods.

It’s also very common for most material manufacturers to use additives (especially in PLA). I checked with Spectrum on this and they do add a small amount of impact modifier to help with flexibility. I had suspected this as forming tight coils on small reels can lead to material breakage when unwinding, unless a modifier is used.

I have generally not observed any printing problems or benefits caused by impact modifiers in the plastic, but I have seen many issues with tightly wound reels in the past. These typically manifest as increased force required to extrude as the material is in a tight arc and extra pull-back on the extruder feed. In one example with 3mm PLA and a 50mm inner diameter cored reels, I had the entire Z carriage of the 3D printer lifting up from the pull-back on the tightly wound filament, this at first caused poor quality printing and then as the reel reached the last 1/3 the Z carriage lifted completely off and total print mayhem ensued. I’m very wary ever since.

Melt test, as far as I can tell it smells sweet and melts like natural PLA.

I have in the past seen print quality issues with other types of plastic also being mixed with PLA, this was a more common problem in the early days when 3mm plastic welding reels were being used for 3D printing, many manufacturers now have dedicated processes for 3D printing.

Very first coil ~180mm diameter and last coil ~85mm diameter - 3mm filament Black.

The Spectrum reels have a 75mm inner diameter core, this is about the smallest diameter I would consider for 3mm material. I did not observe any print quality reduction when using both the White and Black 3mm reels even to the end of the coils. My only observation on this would be that I am using a powerful motor and geared extruder for the 3mm drive so I would like to know how well a machine like the Ultimaker 2 that uses a direct drive 3mm extruder manages with this size of coil towards the end.

I have tried to pick up on every important detail in this review, not to be over critical but to highlight both the problems and improvements needed for any material suppliers to consider when producing consumables for the 3D printing market.

The printing properties of this filament are very good indeed, colour is deep and Spectrum have a fantastic range already available, they even have a custom RAL colour matching service.

I have no doubt that with direct control over the manufacture, Spectrum can refine the quality and dimension consistency for this material.

I do hope for a better solution to the reel mounting and feeding; but, I do have a 3D printer (or two), so making a custom spool holder for this size of reel is not out of the question. Another suggestion would be that Spectrum could offer an STL file for a spool holder for customers to print.

Other than that, I would love to be bold and suggest that we all try for a universal filament spool size, but I know that is going to take some time and effort to do — doesn’t mean we shouldn’t try though.

As a professional courtesy, 3DPI’s Editor gave Spectrum Filament a preview copy of this review. This is their pro-active and encouraging response: 

We are pleased with the positive appaisal Richard gave to the printing properties and colour range we supply. With regards to the issues he raised, we would like to emphasise that we are a responsive supplier and keen to work with the 3D printing community to improve filament quality.

Spectrum-new-filament_packagingAs an example of this, I’ve attached a picture of our new packaging. Richard had mentioned his worries about packaging dust in an earlier communication. Since then we have begun to wrap all shipped filament in cellophane to reduce the risk of dust. We have also started labelling each individual box and reel to make our packaging more convenient. We hope this goes some small way to provide tangible evidence of our responsiveness to feedback.

Since we received the review copy we have also begun to examine the issues that arose with some of Richard’s filament and provide solutions. Spectrum is committed to working with the community to provide the best filament available on the market.

Sours: https://3dprintingindustry.com/news/richrap-reviews-spectrum-filament-3d-printing-24446/

Paper Spectrum Paper Printer Paper Review

Starting life as a paper supplier to professionals seven years ago, Paper Spectrum moved into the inkjet printing market when the digital bubble began to expand. Realising that the products on offer were of some benefit to photographers, they expanded their market.

Now with multiple brands in stock as well as their own lines, Paper Spectrum appear to be a forced to be reckoned with.

Paper Spectrum Professional Printing results
The printer used was the new Epson Stylus Photo RX685 and the sample image is the Sample test template. The test is to check the paper for durability, colour reproduction and quality.

The test all papers go through can be viewed in our article here.

Paper Spectrum Professional Pinnacle Gloss 270gsm
The top line paper from Paper Spectrum feels ultra smooth and is a dazzling white. All the Pinnacle series papers are microporous with ozone and UV absorbers for extended print life.

The paper was dry by the time it had flopped to the tray. It was slightly tacky to start with and still a little tacky after 5 minutes. The image didn't smudge with the smudge test but stained badly with coffee and let the colours run with the water. The scratch test took the paper off after scratching with a 2p piece, but held its own against my fingernail.

During the fade test, the paper was left in the window for a week and looking at the scanned images full size, there is an ever so slight decrease in saturation on the shaded side of the hydrant.

Pinnacle Gloss 270gsm
The resilience test.
Pinnacle Gloss 270gsm
The fade test.

Paper Spectrum Professional Premium Satin 240gsm
As a mid weight paper, it feels well made and, like the Pinnacle paper, is a delicious white.
The paper wasn't wet when it came out of the printer, but was a little sticky to the touch. Didn't feel the same after one minute and had lost all stickiness after 5 minutes.

Coffee left a pale yellow stain and colours started to move away from the liquid, hence the purple tide mark around the coffee and water stain.

Despite the initial stickiness of the paper, it didn't smudge at all and the scratch test was a better result than the Glossy paper. Minimal removal of resin with the 2p piece and my fingernail didn't mark it either.

The whole image of the fade test looks paler, which could be down to scanning. No scans had any adjustments made, so should come out exactly the same unless the paper is faded.

Premium Satin 240gsm

The resilience test.

Premium Satin 240gsm
The fade test.

Paper Spectrum Professional Studio Matt 200gsm
The paper is a softer fibre feeling like a card to the touch and is designed for the fine art side of printing. Its whiteness is not as proud as the Pinnacle or Premium, but I put that down to the material.
Straight out of the printer, the paper was completely dry, no stickiness at all.

After thee minutes, the water had turned the paper yellow and the inks were repulsing away from it causing a deep purple line around the edge. Coffee gave a similar result to the others.

The paper did start to rub away with the scratch test but, unusually, in a reverse order from the other two papers. The 2p piece scratch test removed less than my fingernail as it scratched off the majority of colour, whilst the 2p piece hardly marked it at all.

Studio Matt 200gsm
The resilience test.
Studio Matt 200gsm
The fade test.


Paper Spectrum Professional Verdict
The paper I tested wasn't the most resilient, but the colours were bright and the paper took the ink well.

I'm disappointed with the results of the water, with the colours running out of the paper, but the stains are to be expected.

The price of the paper is excellent at 50 A4 sheets for £9.99, so if you need a lot of paper on a budget, take a look.

Paper Spectrum Professional Plus points
Great value for money
Good colour reproduction
Instant drying

Paper Spectrum Professional Minus points
Inks create a tidemark around water
Resin can scratch off

PRINT QUALITY

COLOUR REPRODUCTION

PERFORMANCE

OVERALL

The Pinnacle range of paper starts at £9.99 for 40 A4 sheets.

The Premium range starts at £9.99 for 50 A4 sheets.

The Studio Matt paper starts at £14.99 for a pack of 100 A4 sheets.

Paper Spectrum paper can be purchased from the Paper Spectrum website here.

 

MPB Start Shopping

Support this site by making a Donation, purchasing Plus Membership, or shopping with one of our affiliates: Amazon UK, Amazon US, Amazon CA, ebay UK

It doesn't cost you anything extra when you use these links, but it does support the site, helping keep ePHOTOzine free to use, thank you.
Sours: https://www.ephotozine.com/article/paper-spectrum-paper-printer-paper-review-7982
  1. Penn state football pro day
  2. Cheese at safeway
  3. Twitch addons
  4. Fap ceo

Business Review

Spectrum Printing & Marketing's Small Business Review

Business Review                                

What is a business review?

Don’t worry, The Happy Printers won’t start being a business coach and talk P&L with you.

We want to look at your business from a customer’s view.  What’s your brand?  What do you?  How are you different?

Remember if you are not becoming more memorable in your customer eyes you are being forgotten.  That means your competitor is winning YOUR business and maybe even getting YOUR customers.

We also like to look at pricing to ensure it’s fair, reasonable, market driven.  Plus your pricing must have enough profit for growth and expansion.  Pricing is merely a sales tool.

How can a printing company help my small business with a business review?  It’s simple, Dick Olenych, the original Happy Printer is a small business expert.  He helps small businesses all the time. 

And by the way the first hour session is free…and sometimes the second one is too.  Just ask us.

Did you know that Spectrum Printing, The Happy Printers, is the best commercial printer in SE Virginia…and maybe all of North America?  We are also a marketing company that focuses on the needs of small businesses.

If you like our tagline, The Happy Printers and understand that we do NOT sell print, we sell happy, then you’ll know our brand and see how it is part of our DNA.

The Happy Printers are your commercial printer & marketing company. Everything from business reviews, brand development, marketing and advertising should bring potential clients closer.  Let us help you generate more visibility and leads by helping your small business with the marketing basics.  And don’t forget, we also can help you with your printing needs.

If your company is located at the beach in Norfolk, Virginia Beach, Red Mill, Chesapeake, Chester, Newport News, Yorktown, or Richmond, The Happy Printers can help your small or medium size business understand your marketing needs through a business review.  We’re sure that’ll make you happy.

The Happy Printers was voted the BEST of the best commercial printer in Hampton Roads for 2011, the best business card printer company in 2012, the best brochure printing company in 2013, the best EDDM print shop 2014, the best direct mail printer in 2015, the best wide format printer in 2016 and once again the best of the best commercial printer in 2017.  That’s right, for seven years Spectrum Printing, your small business marketing partner has been voted the best printer because we deliver what our customers want – marketing, advertising and print knowledge.

Before Spectrum Printing, Dick Olenych was the National Marketing Director for a multi-billion-dollar international corporation…yeah, he knows a little bit about marketing and advertising.  And he can help your small business too.  He’s even taught marketing at the university level.

ABOUT OUR PRINT SHOP

The Happy Printers is an award-winning printer and marketing company that consults with clients on their marketing, advertising and printing needs.  We also offer exceptional offset and digital printing services for clients in Eastern Virginia, Richmond, Eastern Shore, Philly and Baltimore, Delaware.  And, don’t forget “We beat Vista” on many of our printed products like, booklets, brochures, large catalogs, NCR forms, and more!

Contact us at:

[email protected]

757 473.9977

Sours: https://www.thehappyprinters.com/
Canon G650/G620 MegaTank photo printer review - Very low costs prints - Quality, speed, features

Spectrum Printing Employee Reviews

A fun place to work with good people

Customer Service (Former Employee) - Rockville, MD - October 2, 2013

Spectrum was a good place to work. The owner was both fair and hands on, the staff were friendly and professional, and the work was satisfying. I enjoyed helping customers meet their deadlines and expectations, and I was fond of the interaction with both my co-workers and my customers.
I was responsible for writing up job orders with the proper specifications, communicating with clients, communicating with vendors, sending either electronic or hard proofs to clients for approval, meeting project deadlines, writing purchase orders, overseeing that any changes that may have be made are done correctly, communicating with co-workers as to production expectations, and providing estimates and/or invoices to the customer as needed.
The hardest part of the job was staying on top of many different types of projects at different stages of production. Overall, it was a rewarding job, but it was a challenge because of the multitasking involved.

Pros

a kind boss, an hour for lunch, and a decent health plan

Sours: https://www.indeed.com/cmp/Spectrum-Printing/reviews

Printing reviews spectrum

.

Best Colour Laser Printer -- Buying Guide – In 2021

.

Now discussing:

.



1121 1122 1123 1124 1125