Mechanical, toroid gasket that seals an interface
This article is about the mechanical seal. For other uses, see Oring.
An O-ring, also known as a packing or a toric joint, is a mechanical gasket in the shape of a torus; it is a loop of elastomer with a round cross-section, designed to be seated in a groove and compressed during assembly between two or more parts, creating a seal at the interface.
The O-ring may be used in static applications or in dynamic applications where there is relative motion between the parts and the O-ring. Dynamic examples include rotating pump shafts and hydraulic cylinder pistons. Static applications of O-rings may include fluid or gas sealing applications in which: (1) the O-ring is compressed resulting in zero clearance, (2) the O-ring material is vulcanized solid such that it is impermeable to the fluid or gas, and (3) the O-ring material is resistant to degradation by the fluid or gas. The wide range of potential liquids and gases that need to be sealed has necessitated the development of a wide range of materials. 
O-rings are one of the most common seals used in machine design because they are inexpensive, easy to make, reliable and have simple mounting requirements. They have been tested to seal up to 5,000 psi (34 MPa) of pressure. The maximum recommended pressure of an O-ring seal depends on the seal hardness and gland clearance.
O-rings can be produced by extrusion, injection molding, pressure molding or transfer molding.
The first patent for the O-ring, is dated May 12, 1896 as a Swedish patent. J. O. Lundberg, the inventor of the O-ring, received the patent. The US patent  for the O-ring was filed in 1937 by a then 72-year-old Danish-born machinist, Niels Christensen. In his previously filed application in 1933, resulting in Patent 2115383, he opens by saying, "This invention relates to new and useful improvements in hydraulic brakes and more particularly to an improved seal for the pistons of power conveying cylinders." He describes "a circular section ring . . . made of solid rubber or rubber composition", and explains, "this sliding or partial rolling of the ring . . . kneads or works the material of the ring to keep it alive and pliable without deleterious effects of scuffing which are caused by purely static sliding of rubber upon a surface. By this slight turning or kneading action, the life of the ring is prolonged." His application filed in 1937 says that it "is a continuation-in-part of my copending application Serial No. 704,463 for Hydraulic brakes, filed December 29, 1933 now U. S. Patent No. 2,115,383 granted April 26, 1938."
Soon after migrating to the United States in 1891, he patented an air brake system for streetcars (trams). Despite his legal efforts, his intellectual property rights were passed from company to company until they ended up at Westinghouse. During World War II, the US government commandeered the O-ring patent as a critical war-related item and gave the right to manufacture to other organizations. Christensen received a lump sum payment of US$75,000 for his efforts. Litigation resulted in a $100,000 payment to his heirs in 1971, 19 years after his death.
Theory and design
O-rings are available in various metric and inch standard sizes. Sizes are specified by the inside diameter and the cross section diameter (thickness). In the US the most common standard inch sizes are per SAE AS568C specification (e.g. AS568-214). ISO 3601-1:2012 contains the most commonly used standard sizes, both inch and metric, worldwide. The UK also has standards sizes known as BS sizes, typically ranging from BS001 to BS932. Several other size specifications also exist.
Successful O-ring joint design requires a rigid mechanical mounting that applies a predictable deformation to the O-ring. This introduces a calculated mechanical stress at the O-ring contacting surfaces. As long as the pressure of the fluid being contained does not exceed the contact stress of the O-ring, leaking cannot occur. The pressure of the contained fluid transfers through the essentially incompressible O-ring material, and the contact stress rises with increasing pressure. For this reason, an O-ring can easily seal high pressure as long as it does not fail mechanically. The most common failure is extrusion through the mating parts.
The seal is designed to have a point contact between the O-ring and sealing faces. This allows a high local stress, able to contain high pressure, without exceeding the yield stress of the O-ring body. The flexible nature of O-ring materials accommodates imperfections in the mounting parts. But it is still important to maintain good surface finish of those mating parts, especially at low temperatures where the seal rubber reaches its glass transition temperature and becomes increasingly inflexible and glassy. Surface finish is also especially important in dynamic applications. A surface finish that is too rough will abrade the surface of the O-ring, and a surface that is too smooth will not allow the seal to be adequately lubricated by a fluid film.
In vacuum applications, the permeability of the material renders the point contacts unusable. Instead, higher mounting forces are used and the ring fills the whole groove. Also, round back-up rings are used to save the ring from excessive deformation  Because the ring feels the ambient pressure and the partial pressure of gases only at the seal, their gradients will be steep near the seal and shallow in the bulk (opposite to the gradient of the contact stress  See: Vacuum flange#KF.2FQF. High-vacuum systems below 10−9Torr use copper or nickel O-rings. Also, vacuum systems that have to be immersed in liquid nitrogen use indium O-rings, because rubber becomes hard and brittle at low temperatures.
High temperature applications
In some high-temperature applications, O-rings may need to be mounted in a tangentially compressed state, to compensate for the Gow-Joule effect.
O-rings come in a variety of sizes. Society of Automotive Engineers (SAE) Aerospace Standard 568 (AS568) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. British Standard (BS) which are imperial sizes or metric sizes. Typical dimensions of an O-ring are internal dimension (id), outer dimension (od) and thickness / cross section (cs)
Metric O-rings are usually defined by the internal dimension x the cross section. Typical part number for a metric O-ring - ID x CS [material & shore hardness] 2x1N70 = defines this O-ring as 2mm id with 1mm cross section made from Nitrile rubber which is 70Sh. BS O-rings are defined by a standard reference.
The World's Largest O-ring was produced in a successful Guinness World Record attempt by Trelleborg Sealing Solutions Tewkesbury partnered with a group of 20 students from Tewkesbury School. The O-ring once finished and placed around the Medieval Tewkesbury Abbey had a 364 m (1,194 ft) circumference, an approximately 116 m (381 ft) inner diameter, and a cross section of 7.2 mm (0.28 in).
O-ring selection is based on chemical compatibility, application temperature, sealing pressure, lubrication requirements, durometer, size and cost.
Synthetic rubbers - Thermosets:
- Butadiene rubber (BR)
- Butyl rubber (IIR)
- Chlorosulfonated polyethylene (CSM)
- Epichlorohydrin rubber(ECH, ECO)
- Ethylene propylene diene monomer (EPDM): good resistance to hot water and steam, detergents, caustic potash solutions, sodium hydroxide solutions, silicone oils and greases, many polar solvents and many diluted acids and chemicals. Special formulations are excellent for use with glycol-based brake fluids. Unsuitable for use with mineral oil products: lubricants, oils, or fuels. Peroxide-cured compounds are suitable for higher temperatures.
- Ethylene propylene rubber (EPR)
- Fluoroelastomer (FKM): noted for their very high resistance to heat and a wide variety of chemicals. Other key benefits include excellent resistance to aging and ozone, very low gas permeability and the fact that the materials are self-extinguishing. Standard FKM materials have excellent resistance to mineral oils and greases, aliphatic, aromatic and chlorinated hydrocarbons, fuels, non-flammable hydraulic fluids (HFD) and many organic solvents and chemicals. Generally not resistant to hot water, steam, polar solvents, glycol-based brake fluids and low molecular weight organic acids. In addition to the standard FKM materials, a number of specialty materials with different monomer compositions and fluorine content (65% to 71%) are available that offer improved chemical or temperature resistance and/or better low temperature performance.
- Nitrile rubber (NBR, HNBR, HSN, Buna-N): a common material for o-rings because of its good mechanical properties, its resistance to lubricants and greases, and its relatively low cost. The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer: low content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels. As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves. Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer. Peroxide-cured materials have improved physical properties, chemical resistance and thermal properties, as compared to sulfur-donor-cured materials. Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 176 °F (80 °C). NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol-based brake fluids and non-flammable hydraulic fluids (HFD). NBR also has low resistance to ozone, weathering and aging. HNBR has considerable improvement of the resistance to heat, ozone and aging, and gives it good mechanical properties.
- Perfluoroelastomer (FFKM)
- Polyacrylate rubber (ACM)
- Polychloroprene (neoprene) (CR)
- Polyisoprene (IR)
- Polysulfide rubber (PSR)
- Polytetrafluoroethylene (PTFE)
- Sanifluor (FEPM)
- Silicone rubber (SiR): noted for their ability to be used over a wide temperature range and for excellent resistance to ozone, weathering and aging. Compared with most other sealing elastomers, the physical properties of silicones are poor. Generally, silicone materials are physiologically harmless so they are commonly used by the food and drug industries. Standard silicones are resistant to water up to 212 °F (100 °C), aliphatic engine and transmission oils and animal and plant oils and fats. Silicones are generally not resistant to fuels, aromatic mineral oils, steam (short term to 248 °F (120 °C) is possible), silicone oils and greases, acids or alkalis. Fluorosilicone elastomers are far more resistant to oils and fuels. The temperature range of applications is somewhat more restricted.
- Styrene-butadiene rubber (SBR)
- Thermoplastic elastomer (TPE) styrenics
- Thermoplastic polyolefin (TPO) LDPE, HDPE, LLDPE, ULDPE
- Thermoplastic polyurethane (TPU) polyether, polyester: Polyurethanes differ from classic elastomers in that they have much better mechanical properties. In particular they have a high resistance to abrasion, wear and extrusion, a high tensile strength and excellent tear resistance. Polyurethanes are generally resistant to aging and ozone, mineral oils and greases, silicone oils and greases, nonflammable hydraulic fluids HFA & HFB, water up to 122 °F (50 °C) and aliphatic hydrocarbons.
- Thermoplastic etheresterelastomers (TEEEs) copolyesters
- Thermoplastic polyamide (PEBA) Polyamides
- Melt Processible Rubber (MPR)
- Thermoplastic Vulcanizate (TPV)
- Air, 200 to 300 °F (93 to 149 °C) – Silicone
- Beer - EPDM
- Chlorine Water – Viton (FKM)
- Gasoline – Buna-N or Viton (FKM)
- Hydraulic Oil (Petroleum Base, Industrial) – Buna-N
- Hydraulic Oils (Synthetic Base) – Viton
- Water – EPDM
- Motor Oils – Buna-N
Although the O-ring was originally so named because of its circular cross section, there are now variations in cross-section design. The shape can have different profiles, such as an x-shaped profile, commonly called the X-ring, Q-ring, or by the trademarked name Quad Ring. When squeezed upon installation, they seal with 4 contact surfaces—2 small contact surfaces on the top and bottom. This contrasts with the standard O-ring's comparatively larger single contact surfaces top and bottom. X-rings are most commonly used in reciprocating applications, where they provide reduced running and breakout friction and reduced risk of spiraling when compared to O-rings.
There are also rings with a square profile, commonly called square-cuts, lathe cuts, tabular cut or Square rings. When O-rings were selling at a premium because of the novelty, lack of efficient manufacturing processes and high labor content, Square rings were introduced as an economical substitution for O-rings. The square ring is typically manufactured by molding an elastomer sleeve which is then lathe-cut. This style of seal is sometimes less expensive to manufacture with certain materials and molding technologies (compression molding, transfer molding, injection molding), especially in low volumes. The physical sealing performance of square rings in static applications is superior to that of O-rings, however in dynamic applications it is inferior to that of O-rings. Square rings are usually used only in dynamic applications as energizers in cap seal assemblies. Square rings can also be more difficult to install than O-rings.
Similar devices with a non-round cross-sections are called seals, packings or gaskets. See also washers.
Automotive cylinder heads are typically sealed by flat gaskets faced with copper.
Knife edges pressed into copper gaskets are used for high vacuum.
Elastomers or soft metals that solidify in place are used as seals.
O-ring materials may be subjected to high or low temperatures, chemical attack, vibration, abrasion, and movement. Elastomers are selected according to the situation.
There are O-ring materials which can tolerate temperatures as low as −328.0 °F (−200 °C) or as high as 482 °F (250 °C). At the low end, nearly all engineering materials become rigid and fail to seal; at the high end, the materials often burn or decompose. Chemical attack can degrade the material, start brittle cracks or cause it to swell. For example, NBR seals can crack when exposed to ozone gas at very low concentrations, unless protected. Swelling by contact with a low viscosity fluid causes an increase in dimensions, and also lowers the tensile strength of the rubber. Other failures can be caused by using the wrong size of ring for a specific recess, which may cause extrusion of the rubber.
Elastomers are sensitive to ionizing radiation. In typical applications, O-rings are well protected from less penetrating radiation such as ultraviolet and soft X-rays, but more penetrating radiation such as neutrons may cause rapid deterioration. In such environments, soft metal seals are used.
There are a few common reasons for O-Ring Failure:
1. Installation Damage – This is caused by improper installation of the O-ring.
2. Spiral Failure – Found on long-stroke piston seals and – to a lesser degree – on rod seals. The seal gets “hung up” at one point on its diameter (against the cylinder wall) and slides and rolls at the same time. This twists the O-ring as the sealed device is cycled and finally causes a series of deep spiral cuts (typically at a 45 degree angle) on the surface of the seal.
3. Explosive Decompression - An O-ring embolism, also called gas expansion rupture, occurs when high pressure gas becomes trapped inside the elastomeric seal element. This expansion causes blisters and ruptures on the surface of the seal.
Main article: Space Shuttle Challenger disaster
The failure of an O-ring seal was determined to be the cause of the Space Shuttle Challenger disaster on January 28, 1986. A crucial factor was cold weather prior to the launch. This was famously demonstrated on television by Caltech physics professor Richard Feynman, when he placed a small O-ring into ice-cold water, and subsequently showed its loss of flexibility before an investigative committee.
The material of the failed O-ring was FKM, which was specified by the shuttle motor contractor, Morton-Thiokol. When an O-ring is cooled below its glass transition temperature Tg, it loses its elasticity and becomes brittle. More importantly, when an O-ring is cooled near (but not beyond) its Tg, the cold O-ring, once compressed, will take longer than normal to return to its original shape. O-rings (and all other seals) work by creating positive pressure against a surface, thereby preventing leaks. On the night before the launch, exceedingly low air temperatures were recorded. On account of this, NASA technicians performed an inspection. The ambient temperature was within launch parameters, and the launch sequence was allowed to proceed. However, the temperature of the rubber O-rings remained significantly lower than that of the surrounding air. During his investigation of the launch footage, Feynman observed a small out-gassing event from the Solid Rocket Booster at the joint between two segments in the moments immediately preceding the disaster. This was blamed on a failed O-ring seal. The escaping high-temperature gas impinged upon the external tank, and the entire vehicle was destroyed as a result.
The rubber industry has gone through its share of transformation after the accident. Many O-rings now come with batch and cure date coding, as in the medicine industry, to precisely track and control distribution. For aerospace and military/defense applications, O-rings are usually individually packaged and labeled with the material, cure date, and batch information. O-rings can, if needed, be recalled off the shelf. Furthermore, O-rings and other seals are routinely batch-tested for quality control by the manufacturers, and often undergo Q/A several more times by the distributor and ultimate end users.
As for the boosters themselves, NASA and Morton-Thiokol redesigned them with a new joint design, which now incorporated three O-rings instead of two, with the joints themselves having onboard heaters that can be turned on when temperatures drop below 50 °F (10 °C). No O-ring issues have occurred since Challenger, and they did not play a role in the Space Shuttle Columbia disaster of 2003.
An O-ring is one of the simplest, yet highly critical, precision mechanical components ever developed. But, there are new advances that may take some of the burden of critical sealing away from the O-ring. There are cottage industries of elastomer consultants assisting in designing O-ring-less pressure vessels. Nano-technology-rubber is one such new frontier. Presently, these advancements are increasing the importance of O-rings. Since O-rings encompass the areas of chemistry and material science, any advancement in nano-rubber will affect the O-ring industry.
Already, there are elastomers filled with nano-carbon and nano-PTFE and molded into O-rings used in high-performance applications. For example, carbon nanotubes are used in electrostatic dissipative applications and nano-PTFE is used in ultra pure semiconductor applications. The use of nano-PTFE in fluoroelastomers and perfluoroelastomers improves abrasion resistance, lowers friction, lowers permeation, and can act as clean filler.
Using conductive carbon black or other fillers can exhibit the useful properties of conductive rubber, namely preventing electrical arcing, static sparks, and the overall build-up of charge within rubber that may cause it to behave like a capacitor (electrostatic dissipative). By dissipating these charges, these materials, which include doped carbon-black and rubber with metal filling additives, reduce the risk of ignition, which can be useful for fuel lines.
ISO 3601 Fluid power systems — O-rings
- ^Whitlock, Jerry (2004). "The Seal Man's O-Ring Handbook"(PDF). EPM, Inc. - The Seal Man. Archived from the original(PDF) on 2019-08-10. Retrieved 2018-12-08.
- ^"GFS O-Rings". Gallagher Seals. Retrieved 4 August 2021.
- ^Pearl, D.R. (January 1947). O-Ring Seals in the Design of Hydraulic Mechanisms. S.A.E. Annual Meeting. Hamilton Standard Prop. Div. of United Aircraft Corp.
- ^"Frequently Asked O-ring Technical Questions". Parker O-Ring & Engineered Seals Division. Retrieved December 7, 2018.
- ^"O-Ring - Who Invented the O-Ring?". Inventors.about.com. 2010-06-15. Archived from the original on 2009-03-15. Retrieved 2011-03-25.
- ^US patent 2180795, Niels A. Christensen, issued 1939-11-21
- ^2180795, Christensen, Niels A., "Packing", issued 1939-11-21 , applied 1937-10-02
- ^ ab"No. 555: O-Ring". Uh.edu. 2004-08-01. Retrieved 2011-03-25.
- ^2115383, Christensen, Niels A., "Hydraulic brake", issued 1938-04-26 , applied 1933-12-29
- ^"Sealing system eliminates O-rings: News from John Crane". Engineeringtalk.com. 2001-07-16. Retrieved 2011-03-25.
- ^"Archived copy". Archived from the original on 2007-09-21. Retrieved 2008-01-25.CS1 maint: archived copy as title (link)
- ^"MDC Vacuum Products-Vacuum Components, Chambers, Valves, Flanges & Fittings". Mdc-vacuum.com. Retrieved 2011-03-25.
- ^"O-ring". Glossary.oilfield.slb.com. Archived from the original on 2011-06-07. Retrieved 2011-03-25.
- ^"AS568: Aerospace Size Standard for O-Rings - SAE International". www.sae.org. Retrieved 2018-02-20.
- ^"O-ring Design, O-ring Design Guide, O-ring Seal Design -Mykin Inc". Mykin.com. Retrieved 2011-03-25.
- ^ abcde"Type details". O-ring elastomer. Dichtomatik Americas. 2012. Retrieved 9 April 2013.
- ^"Chemical Compatibility". The O-Ring Store LLC.
- ^"X-ring simulation".
- ^"John Crane seals measure up to API standards: News from John Crane EAA". Processingtalk.com. 2005-12-09. Archived from the original on 2009-02-24. Retrieved 2011-03-25.
- ^"What is O-Ring Shelf Life?". Oringsusa.com. Retrieved 2011-03-25.
|Wikimedia Commons has media related to O-rings.|
Car O-Ring Assortment
We offer a great car O-ring assortment for your automotive O-ring sealing needs. This includes BUNA-N O rings measured in both inches and millimeters. BUNA-N, which is also known as nitrile, is a synthetic rubber that's highly resistant to many chemicals, oils, fuels and even diluted acids. This makes it ideal for use in the manufacture of rubber seals for cars and auto rubber O-rings.
You'll find a wide variety of car seals and O-rings here, with various thicknesses, inside and outside diameters. There are several subcategories of air conditioning O-rings, including those designed for use only with R12 refrigerant, and Teflon-coated blue neoprene air conditioning O-rings for use with either R12 or R134A refrigerants. You'll also find a selection of green nitrile air conditioning O-rings, also for use with R12 of R134A refrigerants, several of which are direct replacements for O-rings found on Ford, Nissan, Toyota and Acura automobiles.
Review: 12 Months With the EXT Era Fork - Pinkbik__ Pinkbik__A Week On The Wrist: The Rolex Submariner Ref. 1 – Early Season MTB Checkup - Teton Gravity Research Teton Gravity ResearchA single fastener supplier for the professional - Fastener + Fixing Magazine Fastener + Fixing MagazineInline thickness, profile and width measurement systems - Design Products Applications Design Products ApplicationsFirst Ride: RockShox's Updated DebonAir Air Spring - Pond Beaver 2020 - Pinkbik__ Pinkbik__Field Test: 2021 Ibis Mojo 4 - The Trail Rider's Trail Bike - Pinkbik__ Pinkbik__21 Best Samsung Galaxy S10 Plus Cases (2021) - Heav__ Heav__A Week On The Wrist: The A. Reviews, Features and More - Mac Rumors Mac RumorsTacx NEO Bike Smart In-Depth Review - DC Rainmaker DC RainmakerReview: GT's 2019 Fury 29' Combines 4-Bar High Pivot Suspension Designs - Pinkbik__ Pinkbik__Stan's Arch MK3 Rim - Review - Pinkbik__ Pinkbik__What You Need to Know About Moisture-Proof Cable Assemblies - ENGINEERIN__ ENGINEERIN__Ibis Mojo 3 - Review - Pinkbik__ Pinkbik__Watches Wonders 2020: the best timepieces unveiled at the world's first virtual watch show | Watches | Watches Jewellery - Luxury London Luxury LondonFAA proposes remote ID rule for drones - Aerospace Manufacturing and Design Aerospace Manufacturing and Design2018 Specialized Diverge, CruX, and Allez revealed - CyclingTips CyclingTipsFGF 524 – The Conversation Starting Edition - Singletrack Magazine Singletrack MagazineFouriers, Birzman and HT - Taipei Show 2015 - Pinkbik__ Pinkbik__$650 Acer Swift 3 vs. $1,800 Apple MacBook Pro: The winner will surprise you - Laptop Mag Laptop MagHomemade Masks In A Time Of Shortage - Hackaday HackadayPolar Vantage V Multisport GPS In-Depth Review - DC Rainmaker DC RainmakerBike Gears Slipping - Ways You Damage Cycling Gear - Bicycling BicyclingLas Vegas Cirque du Cycling, Lap Two - Interbike 2017 - Pinkbik__ Pinkbik__Have Your Say on the Ever-Changing Bike Standards - Pinkbik__ Pinkbik__Riding Rocky Mountain's 2018 Altitude - First Ride - Pinkbik__ Pinkbik__Time frame: a Swedish architect puts a spin on Bravur - Wallpaper* Wallpaper*PowerA Fusion Pro Controller review: Luxury features at a low price on Xbox One and Windows - Windows Central Windows CentralReview: Fox 36 GRIP2 vs. RockShox Lyrik RC2 Fork - Pinkbik__ Pinkbik__MacBook Pro (16-inch, 2019) review: Escaping the butterfly effect - CNET CNETPhoto Epic: When it Rains it Pours - Albstadt World Cup XC 2019 - Pinkbik__ Pinkbik__Best-ever Nexus sets new standard for big-screen Android value - CNET CNETCorsair Scimitar review: A gaming mouse for MMOs, MOBAs, and more - Windows Central Windows CentralJRA with the Angry Asian: Does frame compliance still matter? - CyclingTips CyclingTipsSony Xperia XZ review: The best of Sony, but not the best phone - CNET CNETRugged Tablet PCs: Winmate I980 - Rugged PC Review Rugged PC ReviewCommencal Meta V4 Race - Review - Pinkbik__ Pinkbik__Royal Wedding cake baker Fiona Cairns reveals how you can conquer castles - Daily Mail Daily MailMedical device recalls for August 2014 - Mass Device Mass DeviceFOX Announces 2016 FLOAT 34 for 27.5+ - Pinkbik__ Pinkbik__2017 Scott Spark and Scale - First Look - Pinkbik__ Pinkbik__Component, accessory highlights from the 2016 Sea Otter Classic - CyclingTips CyclingTipsFirst Ride: 2019 RockShox Lyrik RC2 - Pinkbik__ Pinkbik__2016 Turner RFX v4.0 Enduro - Review - Pinkbik__ Pinkbik__
O-Ring & Rubber Seals - Over 30,000 Available Online from Polymax UK
O-ring Manufacturers | O-ring Sizes | O-rings UK
Polymax are one of the largest online distributors of O-rings in the UK. Our comprehensive range is suitable for all kinds of demanding applications and industry needs. Require a non-standard O-ring? our expert sales team is here to help, we’re able to supply many alternative compounds with a short lead time. Polymers such as silicone, EPDM, Kalrez®, FFKM, HNBR, PTFE, XNBR, PU, CR and more. In addition to this we can supply 0-rings in unique colours, materials or specifications to meet certification standards. With over 30,000 different materials and sizes available to buy online, trust us to provide the O-ring you need.
Can't find what you need? Contact one of our experts. Call +44 (0)1420 474123 or email [email protected]
Nitrile (NBR) O-Rings | Buy Online
Cost effective with the biggest choice of sizes available to buy online. Commonly used in applications requiring resistance to oil, fat and grease. (-30°C to +90°C).
Viton® (FKM) O-Rings | Buy Online
FKM O-rings are typically used in applications where resistance to wide range of chemicals and high temperature is crucial. (-15°C to +200°C).
EPDM O-Rings | Buy Online
Excellent resistance to weathering, ozone and steam. Used in braking systems using glycol (Dot 3 and 4) and silicone based fluids (Dot 5). (-30°C to +125°C).
Silicone O-Rings | Buy Online
Excellent resistance to temperature extremes, flexible at low temperatures. Used in many food and pharmaceutical applications. (-40°C to +200°C).
PTFE O-Rings | Buy Online
A tough abrasion and chemical resistant compound, yet with less elasticity than some materials. (-200°C to +250°C).
Neoprene® O-Rings | Buy Online
Chloroprene is a good multi-purpose material, it exhibits fair oil resistance and good ozone and weather resistance. (-40°C to +110°C).
FEP Encapsulated O-Rings
An encapsulated O-ring comprises an elastomer energising core, which has a seamless fluoropolymer jacket. (-20°C to +200°C).
PTFE Backup / Support O-Rings
Back-up rings are used with O-rings for both static and dynamic sealing applications.
Polymax FFKM O-Rings
One of the most durable and resilient O-ring materials. A popular choice for enduring harsh environments. (-0°C to +330°C).
Kalrez® (FFKM) O-Rings
Outstanding chemical and temperature resistance, with lots of non-standard options. (-50°C to +350°C).
HNBR is treated with hydrogen producing high strength, greater thermal stability and reduced wear. (-30°C to +170°C).
A unique compound that is often used in the automotive industry. Resistant to petroleum, steam, and other automotive fluids. (-5°C to 204°C).
FEP Encapsulated Gaskets
FEP Encapsulated Gaskets are designed to withstand almost all industrial chemicals and solvents.
Bonded Seals | Buy Online
Bonded seals (or Dowty seals) are metal washer/rubber bonded inserts for use in high pressure applications where conventional seals are unsuitable.
O-Ring Grease | Buy Online
O-ring synthetic lubricant is used to prolong O-ring performance and assist in assembly.
O-Ring Kits & Cord Kits | Buy Online
A range of O-ring kits in various different materials, including NBR, Viton®, EPDM, HNBR and Silicone.
O rings rubber thick
.How to Measure an O Ring (with only basic tools)
- Roku model 3900x ip address
- Echo salt spreader
- Vans sport center
- Radio romance wiki
- Walmart bicycles out of stock
- Synonym for could not
- Get filename without extension cpp
- Virginia department of taxation phone number
- Foreclosures in area